Getting Familiar with Plumbing: A Must for Bathtub Installation
Getting Familiar with Plumbing: A Must for Bathtub Installation
Blog Article
This great article down below involving Installing A Bathtub is truly motivating. Check it out yourself and decide what you think of it.
Setting up a bath tub isn't precisely rocket science, but it does require strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a new one is also a reasonably challenging project. If the old bathtub is easily accessible, the project can move rapidly; if you have to open up a wall surface to remove the old tub as well as position the new bathtub, the task is much harder. In either instance, the project is within a home handyman's abilities, although you will need an assistant to leave the old bathtub and also embeded in the new one. Make certain you have actually certified on your own for the work as well as are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed task, it is far better to think about employing one before you begin. Opportunities are you might require a professional plumber to make tube links.
This write-up will certainly aid you install a brand-new bathtub in your bathroom if you have actually already acquired a new bathtub and do not require to change the plan of your previous water supply pipes.
Your devices and material checklist ought to make up the following:
Getting ready for the Setup
First of all, the sustaining frame provided with the bathroom should be fitted (if needed) according to the supplier's guidelines. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the taps system to avoid strain on the bathtub.
Fit the versatile faucet adapters to the bottom of both faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Ensure you make use of every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently be ready to be suited its last position.
Removing Old Taps
If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is detach the supply of water. After doing so, switch on the taps to drain any water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly troublesome as a result of the limited access that is typically the case.
Utilize a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that attaches the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly originate from the pipelines. When the supply pipelines have actually been gotten rid of, make use of the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will need to stop the solitary faucets from turning throughout this procedure. As soon as the faucets have been gotten rid of, the holes in the bath/basin will certainly need to be cleansed of any old securing compound.
Prior to proceeding to fit the brand-new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old faucets are longer than the new faucets, then a shank adapter is required for the new faucets to fit.
Mounting the Tub
Using both wood boards under its feet, put the bath tub in the called for setting. The wooden boards are useful in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 small points.
The following objective is to make certain that the tub is leveled all round. This can be attained by examining the level as well as changing the feet on the bath tub until the spirit level reviews degree.
To mount faucets, fit the bottom of the outermost versatile faucet connector to the ideal supply pipeline by making a compression sign up with; then do the exact same for the various other tap.
Turn on the water system and check all joints as well as new pipework for leakages and also tighten them if required. Load the tub as well as also examine the overflow electrical outlet and the typical outlet for leaks.
Finally, fix the bath paneling as described in the maker's user's manual. Tiling and sealing around the bath tub needs to wait till the bathtub has actually been used a minimum of once as this will resolve it into its last placement.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will need a plastic connector to prevent damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, then you will certainly require decreasing couplers, which links the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin ensuring that the washing machines remain in location between the tap and the sink. Protect the faucet in place with the supplier offered backnut. Once the tap is securely in position, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former type should be attached to the tap finishes initially, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten both ends with a spanner after both ends have been attached.
Tiling Around the Tub
In the location where the bathroom satisfies the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split an inflexible seal, creating the water to permeate the wall between the bathroom as well as the tiling, leading to difficulties with dampness and also possible leakages to the ceiling below.
You can pick from a variety of coloured sealers to assimilate your components and fittings. They are sold in tubes and cartridges, and are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger space to fill, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly fill the bath tub with water prior to securing, to enable the movement experienced when the tub remains in usage. The sealer can split rather early if you do not take into consideration this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily readily available on the market. It is advisable to fit the tiles using water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We were introduced to that report on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround through a good friend on a different web property. In case you enjoyed reading our page kindly make sure you remember to share it. I am grateful for your time. Come back soon.
Leak detection needed? Report this page